Close
Filters
Search

Acrylic sealant Textured acrylic

Article No. 0892160500
Textured acrylic ACRYSEAL-FLEX-STRUCTURE-WHITE-310ML
€5.78 inc. VAT price per 1 PCS
LOW STOCK
*
+ -
Particularly suitable for repairing cracks and damage in structured or textured plaster, both indoors and outdoors

Fine-grain texture

An even grain texture is produced by adding high-quality quartz sand.

Can be painted over

Can be painted over with emulsion paints

Resistant to UV and ageing

Odourless

Notice

Attention:

Due to the wide variety of paint and lacquer formulas available, we recommend that you always carry out preliminary testing in order to rule out any interactions. Caution: Sealant joints that have been fully painted over tend to crack when movement occurs in the joint, as the applied paint is generally less elastic than the sealant.

Not suitable for bitumen, civil engineering and underwater joining, on silicate substrates or joints that can be walked or driven on.

Proof of Performance

Tested in accordance with EN 15651 Part 1

  • Fire behaviour: Class E
  • Stability under load: ≤ 3 mm
  • Volume loss: ≤ 25%
  • Tensile behaviour after immersion in water at 23°C (ductile): ≥ 25%
  • Durability: Passed

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Particularly suitable for repairing cracks and damage in structured or textured plaster, both indoors and outdoors

Fine-grain texture

An even grain texture is produced by adding high-quality quartz sand.

Can be painted over

Can be painted over with emulsion paints

Resistant to UV and ageing

Odourless

Notice

Attention:

Due to the wide variety of paint and lacquer formulas available, we recommend that you always carry out preliminary testing in order to rule out any interactions. Caution: Sealant joints that have been fully painted over tend to crack when movement occurs in the joint, as the applied paint is generally less elastic than the sealant.

Not suitable for bitumen, civil engineering and underwater joining, on silicate substrates or joints that can be walked or driven on.

Proof of Performance

Tested in accordance with EN 15651 Part 1

  • Fire behaviour: Class E
  • Stability under load: ≤ 3 mm
  • Volume loss: ≤ 25%
  • Tensile behaviour after immersion in water at 23°C (ductile): ≥ 25%
  • Durability: Passed

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Application area

For sealing joints and cracks on indoor and outdoor structured or textured plaster. Typical surfaces: Plaster, concrete, masonry, gypsum, artificial stone, polystyrene etc.

Instructions

Adhesion surfaces must be clean, dry and firm. Priming improves adhesion to porous and highly absorbent substrates. Mixing ratio of primer: Textured acrylic with water, ratio of 1:1 to 1:5 (depending on viscosity). Old coatings, mortar and cement residues must be removed. Risk of yellowing on contact with white alkyd resin paints cannot be excluded. Risk of corrosion when used on plain iron and non-ferrous metals.


Please observe the "General Notes on Application for Sealants" and "Construction Material Compatibility of Würth Sealants" overview sheet.

Products specifications
Container Cartridge
Contents 310 ml
Fungicidal properties No
Colour White
Chemical basis Acrylate dispersion
Density 1.8 g/cm³
Continuous motion absorption 5 %
Smell/fragrance Odourless
Full curing speed 0.5 mm/d
Fully hardening/curing conditions 23°C and 50% relative humidity
Min. skin-formation time 45 min
Min. breaking elongation 50 %
Breaking elongation conditions for 2-mm film
Conditions for skin-formation time at 23°C and 50% relative humidity
Shore A hardness 28
Min./max. temperature resistance -20 to 75 °C
Min./max. processing temperature 5 to 40 °C
Recoatable/Can be painted over Yes
Surface pre-treatment required On absorbent or porous surfaces
Ratio of ingredients Mixing ratio of acrylic sealant to water = 1:1 to 1:5
Ultraviolet resistance Yes
Coating compatibility Yes
Shelf life from production 18 Month
Conditions to maintain shelf life from production at 10°C to 25°C
Products specifications
Container Cartridge
Contents 310 ml
Fungicidal properties No
Colour White
Chemical basis Acrylate dispersion
Density 1.8 g/cm³
Continuous motion absorption 5 %
Smell/fragrance Odourless
Full curing speed 0.5 mm/d
Fully hardening/curing conditions 23°C and 50% relative humidity
Min. skin-formation time 45 min
Min. breaking elongation 50 %
Breaking elongation conditions for 2-mm film
Conditions for skin-formation time at 23°C and 50% relative humidity
Shore A hardness 28
Min./max. temperature resistance -20 to 75 °C
Min./max. processing temperature 5 to 40 °C
Recoatable/Can be painted over Yes
Surface pre-treatment required On absorbent or porous surfaces
Ratio of ingredients Mixing ratio of acrylic sealant to water = 1:1 to 1:5
Ultraviolet resistance Yes
Coating compatibility Yes
Shelf life from production 18 Month
Conditions to maintain shelf life from production at 10°C to 25°C
Related Product
Close